How to respond when the drawing file is open, damaged

"Drawings can not be opened," "The drawings are open, but the fall in the operation," such as, general how to respond to the situation that occurs when you open a certain drawings are as follows.

There are many reasons unknown problems, etc.

• Case 1 ： AUDIT command
1. Phenomenon will open the drawing that will occur.
2. Run the AUDIT [audit] command.
3. With respect to the following message, enter "Y".
4. ? Are you sure you want to modify the detected error [Yes (Y) / No (N)]:
5. Once preserved by the Save the drawing, to close the open drawings.
6. Open the saved drawing to confirm.

• Case 2 ： PURGE[name deleted] command
1. Phenomenon will open the drawing that will occur.
2. PURGE run the [name deleted] (or -PURGE) command.
3. "Name Display delete items that can be", and then click the "nested item also name Delete" select "all name Delete".
   
4. Close the dialog and click the "Close".
5. Once preserved by the Save the drawing, to close the open drawings.
6. Open the saved drawing to confirm.

• Case 3 ： WBLOCK[block export] command

1. Phenomenon will open the drawing that will occur.
2. Run the WBLOCK [Block Export command.
   
3. Click on the "whole drawing" and specify a destination of the file "OK".
4. Close the open drawings.
5. Make sure to open the exported drawing.

• Case 4 ： Copy and Paste into a new drawing

1. Phenomenon will open the drawing that will occur.
2. COPYCLIP command (shortcut: CTRL + C) and then the run.
3. Select the shape and type "ALL", and press Enter.
4. Open a new drawing.
5. PASTECLIP command (shortcut: CTRL + V) to the run.
6. Enter the "0,0" as the insertion point.
7. Once preserved by the Save the drawing, to close the open drawings.
8. Make sure to open the saved drawing.

• Case ０： Lack of memory
  file size is large, if the CAD on the way is open to end the freeze, please refer to the article below.
  
  
• Problems that are solved by using the 64bit version
  
  
• Case 1 ： RECOVER command
  

1. The IJCAD to new start-up, run the RECOVER command.
2. Phenomenon will click to select the drawings "open" to occur.
3. If the repair is drawing was opened, once preserved by the Save the drawing, to close the open drawings.
4. Make sure to open the saved drawing.

• Case 2 ： INSERT command

1. Start IJCAD, open a new drawing.
2. INSERT [Insert Block] to execute the command.
3. Click the "Browse", phenomenon select a drawing that will occur, and then click "Open".
4. Remove the check from the "Specify on screen" of each item, and then click the "OK" check the "degradation".
5. If you can insert the drawing, once preserved by the Save the drawing, and then close the open drawing.
6. Make sure to open the saved drawing.

• case 3 ： Restoring from SV$ or BAK file

1. Look for the file extension "SV $" or "BAK" by such as Windows Explorer.
   (In the initial state, .sv $ file is the Windows Temp folder, the bak file, located in the same folder as the drawing file.)
   
   Example:
   If the name of the DWG file is "Drawing-A.dwg", "Drawing-A_X_XX_XXXX. sv $ "(" X "is an arbitrary number) will be and" Drawing-A.BAK ".
   
   
2. Change the extension of the "SV $" or "BAK" file to the "DWG".
   
   Example:
   In the case of "Drawing-A_1_23_4567.SV $" and "Drawing-A.BAK",
   and change it to "Drawing-A.dwg".
   Note: Because you can not name change and there are already "Drawing-A.dwg" in the same folder, and change it to not be heavy file names, such as "Drawing-A_1.dwg".
   
   
3. Start IJCAD, make sure to open the file that you renamed.

Examples of sv $ file in the Temp folder

It should be noted that in the standard configuration of the OS, since the extension of SV $ file is a state that does not appear, please choose to view the extension.

• Windows 10
  
• To display the file extension - Windows 7

* Even if the drawing is open, it can be carried out if the (1 to 4) can not be opened.

If you can not repair the drawings also try performing the above, it has become unfortunately unrecoverable data.

If you have an AutoCAD, please try out the repair and audit command of AutoCAD. (There is a case where a point that is not fixed in IJCAD is corrected. On the contrary, not repaired in AutoCAD data, you may be able to repair in IJCAD.)